T238 V1.42 version for V2 gearbox manual

Functions:

1. Low battery voltage protection, the default setting is 7.4V battery. Change the battery when hearing ‘beepbeep beep beep’ 4 times low voltage warning sound.
2. Block-up protection. When gearboxBlock-up occurs, the system stops working and emits an elongated ‘beep’ Please check the wave box immediately by power off.
3. Auto-loading function is designed for gel ball blaster magazines with motor inside, when changing the magazine, the magazine motor will run automatically for a period of time, and the length of time can be programmed by 9th option.
4. This module is able to increase rate of fire, the stability of single-shot and make batteries have higher durability.
5. The energy that support the active brake function comes from the inertia of motor, stop the piston without delay. The effect of active brake is significant on high torque motor
6. The active function prevents the over-spin of gears, this solve the issue that the single shot becomes multiple shot under high voltage. Meanwhile, the spring is fully released in semi-auto modeand parts in gearbox are not under strain, increase the life cycle of gearbox and parts.
7. The system includes multiple shooting mode, these modes can be selected by fire select switch
8. The default position of the piston is adjustable in semi-auto mode. Pre-cocking function can be implementing, zero trigger delay
9. Adjustable rate of fire, the gap between two single shots can be programmable, to achieve adjustable rate of fire
10. When the DTU is overheated, after the trigger is pulled, the motor will give a beep prompt until it is automatically restarted after cooling.

Modes:

SAFE：This mode is completely the same as original safe mode. The trigger is stopped by Safety lever

SEMI: This mode can be programmed to implementing semi-auto, double stroke single shot, 3-round burst to 6-round burst, the default mode is semi auto

AUTO: This mode can be programmed to implementing full-auto, 3-round burst, 6-round burst and 9-round burst, the default mode is Full-auto

Requirements:

1. Silver plate wire is needed for this system, power wire for motor and battery should be larger than 0.5sqm silver plate wire, wire for electronic powered magazine should be around 0.25sqm.
2. High-power soldering iron (higher than 50W) is recommended, solder the clop with 0.5sqm soldering wire and soldering rosin. Please ask professional for help if you do not know to solder.
3. Please use Spring smaller than M150.
4. Use high torque motor can stop the motor fasterand prevent DTU from overheating .
5. In standby state, the current of the system is smaller than 0.01A. Please disconnect the battery if it is not used for a long time.

Installation:

1. Measure the length of each wire according to the wiring diagram then solder the wires on the clip (The exposed solder joint on the PCB clip is not stand too much force, do not pull the wire after the wire is soldered in case damaging the clip)
2. Disassemble the gearbox, it is necessary to take off the cut-off lever, keep the Safety lever and selector plate on the gearbox (Tutorial for disassemble gearbox can be found on YouTube)
3. Install the module and push the wires in the gearbox (some gearbox needs to be cut off stiffener or drilled hole)
4. Assemble the gearbox
5. For more details, scan the QR code

Quick Test:

After soldering, connect the motor. Make sure the wires are connected correctly, then press the trigger button ‘S2’ and connect the battery to it. After the battery is connected, release the trigger button ‘S2’, the the module will run into Quick Test mode. Press each button one by one, you will get two ‘beep’s, if not, your module is not right, contact the customer service immediately.

Programming:

1. Disconnect the battery, thenset the fire selector switch to auto.
2. Connect the battery and pull the trigger in 3 seconds, After  hearing2 long ‘beep~’ , the module runs into programmable mode, otherwise it will be in auto mode.
3. In the programmable mode, the motor emits short ‘beep’, the numbers of ‘beep’ means the serial number of the option. If you want to choose the option, pull and hold the trigger in 2 seconds after ‘beep’s till a long ‘beep’, the module will be set to matched option. (The options and matched function/parameter are in the table below).
4. After setting to the selected option, the motor emitsshort ‘beep’s, the number of ‘beep’s means the different function/parameter of this option. If you want to program to set it to certain option or parameter, pull and hold the trigger in 2 second after ‘beep’ till 2 long ‘beep’, then the module is in programmable mode